Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation



Toyota 4Раннер
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. 4-cylinder engines
   + 3.2. Engines of V6 3,0 l (1993-1994) and 3,4 l (since 1995)
   - 3.3. Dismantle and major maintenance of the engine
      3.3.1. Specifications
      + 3.3.2. Major maintenance
      3.3.3. Engine diagnostics by means of the vacuum gage
      3.3.4. Compression check in engine cylinders
      + 3.3.5. Dismantle of the power unit
      + 3.3.6. Head of cylinders
      3.3.7. Valves
      3.3.8. Shatunno-porshnevaya group
      + 3.3.9. Crankshaft
      3.3.10. Block of cylinders
      3.3.11. Honningovaniye of cylinders
      - 3.3.12. Rods and pistons
         3.3.12.1. Condition check
         3.3.12.2. Installation and check of gaps in shatunny bearings
      3.3.13. Radical and shatunny bearings
      3.3.14. Balansirnye shaft
      3.3.15. Assembly order
      3.3.16. Piston rings
      3.3.17. Engine start-up after repair and a running in
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes



3.3.12. Rods and pistons

3.3.12.1. Condition check

PERFORMANCE ORDER
1. Accurately clear pistons of a deposit and carefully remove rings.
2. Remove a deposit from flutes of piston rings of c with the help of the adaptation (a photo at the left) or an old piston ring (a photo on the right).
3. Wash out pistons and rods solvent, carefully clean drainage oil openings in flutes of the piston and an opening in a rod.
4. If traces of considerable wear are absent and if boring of cylinders is not required, pistons should not be changed. Normal wear is shown in the form of traces of uniform vertical development on a rubbing surface of the piston and in the form of small weakening of landing of the top kompressionny ring. Nevertheless, replacement of piston rings is obligatory.
5. Carefully check existence of cracks on a piston skirt, on lugs of a piston finger and on airfields of piston rings.
6. If on the piston chips and teases are observed, it indicates a frequent overheat of the engine. In this case careful check of systems of greasing and cooling is required. The burn-out of the bottom of the piston testifies to operation of the engine with the wrong installation of the moment of ignition. The reason of an obgoraniye of the bottom of the piston along the edges as a rule is abnormal combustion (detonation). If the specified defects are found, it is necessary to find their reason and to eliminate.
7. Piston corrosion in the form of small poles (petting) testifies to penetration into the combustion chamber (and also in a crankshaft case) cooling liquid.
8. Measure a gap between a flute and a new ring. If the gap exceeds the established limit, it is necessary to replace the piston.
9. Check a gap between the piston and the cylinder, having measured diameter of the cylinder (see subsection 3.3.10) and diameter of the piston from this cylinder.
10. Diameter of the piston is measured perpendicular to an axis of a ralets directly under a finger. If the gap exceeds the established limit, the block of cylinders is subject to boring, and it is necessary to replace pistons and rings repair.
10. Check a gap between a piston finger and a rod head for what shake the piston and a rod in opposite directions. If люфт notable, repair of this connection is necessary.
11. Check of a head of rods and their deformation, and also the corresponding repair are carried out in car-care center.
12. Check existence on rods of cracks and other damages. Remove covers of shatunny bearings, get bearings, wipe landing surfaces on a cover and on a rod, check existence of cracks, scratches and задиров. After check collect a rod, having established into place bearings, tighten nuts by hand.

Prevention

If the engine is disassembled because of jamming, rods are subject to obligatory replacement.