Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation



Toyota 4Раннер
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. 4-cylinder engines
   + 3.2. Engines of V6 3,0 l (1993-1994) and 3,4 l (since 1995)
   - 3.3. Dismantle and major maintenance of the engine
      3.3.1. Specifications
      - 3.3.2. Major maintenance
         3.3.2.1. Alternatives
         3.3.2.2. Order of dismantling of the engine
      3.3.3. Engine diagnostics by means of the vacuum gage
      3.3.4. Compression check in engine cylinders
      + 3.3.5. Dismantle of the power unit
      + 3.3.6. Head of cylinders
      3.3.7. Valves
      3.3.8. Shatunno-porshnevaya group
      + 3.3.9. Crankshaft
      3.3.10. Block of cylinders
      3.3.11. Honningovaniye of cylinders
      + 3.3.12. Rods and pistons
      3.3.13. Radical and shatunny bearings
      3.3.14. Balansirnye shaft
      3.3.15. Assembly order
      3.3.16. Piston rings
      3.3.17. Engine start-up after repair and a running in
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes




3.3.2.2. Order of dismantling of the engine

GENERAL INFORMATION

Krivoshipno-shatunny mechanism and piston group of 4-cylinder engines

1. Ring the kompressionny top
2. Disks of a maslosjemny ring
3. Flywheel
4. Bolt
5. Rod
6. Shatunnye loose leaves
7. Rod cover
8. Epiploon
9. Intensifying plate
10. Holder
11. Detonation sensor
12. Perepuskna cooling branch pipe
13. Fuel filter
14. Laying
15. Hose
16. Support left
17. Radical loose leaf
18. Cover
19. Persistent ring
20. Crankshaft
21. Asterisk
22, 26. Persistent plate
23. Asterisk
24, 25. Balansirny shaft
27. Washer
28. Support right
29. Drain stopper
30. Oil filter
31, 33. Ring
32. Union
34. Lock ring
35. Finger
36. Broad ring
37. Bottom kompressionny ring

Krivoshipno-shatunny mechanism and piston group of engines of V6 3,0 l

1. Detonation sensor
2. Perepuskna branch pipe of cooling of N1
3. For and/m from a manual transmission
4. Flywheel
5. Intensifying plate
6. Epiploon
7. Holder
8. For and/m with automatic transmission
9, 11. Remote washer
10. Leading disk
12. Reduktsionny valve
13, 15. Laying
14. Maslookhladitel
16, 18. Hose

17. Union
19. Pressure sensor
20. To tighten a dinamometrichesky key
21. Framework of covers
22, 25. Persistent half rings
23. Radical loose leaf
24. Crankshaft
26. Adjusting bar of the generator
27. Block of cylinders
28. Rod cover
29. Shatunnye loose leaves
30. Rod
31. Finger
32. Rings
33. Piston
34. Bolt

Krivoshipno-shatunny mechanism and piston group of engines of V6 3,4 l

1. Ring the kompressionny top
2. Ring the kompressionny bottom
3. Disks of a maslosjemny ring
4, 18. Lock ring
5. Plug
6. Rod
7. Shatunnye loose leaves
8. Rod cover
9. Epiploon
10. Holder
11. Block of cylinders
12. Crankshaft
13, 17. Radical loose leaves
14. Framework of covers
15, 16. Persistent half rings
19. Finger
20. Piston
21. Dilator of a maslosjemny ring

The following order of complete dismantling of the engine is recommended:

 – collectors;
 – covers of a head of cylinders;
 – chain cover, chain, drive details (4-cylinder engines);
 – covers of a gear belt a belt, asterisks (on V6 engines);
 – head (and) cylinders;
 – pallet;
 – oil pump;
 – balansirny shaft (4-cylinder engines);
 – rods and pistons;
 – epiploons;
 – crankshaft.