Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Toyota 4Раннер
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
- 9. Suspension bracket and steering
   9.1. Specifications
   9.2. Springs and shock-absorbers (racks) of a forward suspension bracket
   9.3. Stabilizer of a forward suspension bracket
   9.4. Rotary fist
   9.5. Forward nave and bearing
   9.6. Spherical support
   9.7. Top lever
   9.8. Bottom lever
   9.9. Back shock-absorbers
   9.10. Back stabilizer of cross-section stability
   9.11. Cross-section bar of the back bridge
   9.12. Back springs
   9.13. Longitudinal bars of the back bridge
   9.14. Steering wheel
   9.15. Tip of steering drafts
   9.16. Cover of the steering mechanism
   9.17. Steering mechanism
   9.18. Pump of the hydraulic booster
   9.19. Power steering
   9.20. Corners of installation of forward wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes




9.6. Spherical support
GENERAL INFORMATION

Nave, rotary fist and top support of the Toyota 4-Runner/Hilux/Surf car
1. Cover
2. Collar
3. Lock ring
4. Top support
5. Fist
6. Bearing
7. Nave
 8. Epiploon
9. Lock ring
10. Brake board
11. Sensor of speed of ABS system
12. The dividing plug (for and/m with ABS system)
13. Epiploon (all-wheel drive and/m)
14. Cap (rear-wheel and/m)

Bottom support of the Toyota 4-Runner/Hilux/Surf car
1. Bottom support
2, 4. Шплинт
3. Steering draft
 5. Bottom lever
6. Fist

Check люфта in the bottom spherical support

  
1. No more than 2,3 mm

Check

Condition of spherical support it is necessary to check each time when lifting car.

PERFORMANCE ORDER
1. Lift a car front.
2. Clear support and check a condition of sealants.
3. Raise the car, having substituted a jack under the bottom lever of a suspension bracket to unload a support.
4. Shake a wheel mount, at the same time checking люфт in a support (it is carried out with the assistant). If люфт considerable, a support replace (see fig. Check люфта in the bottom spherical support).
5. Shake the top support. Replace a support if it is found considerable люфт.
6. The support should be checked at each removal of a fist or support.
7. For check try to turn a support finger by hand.
8. If the finger is turned by hand, a support replace.
9. The manufacturer recommends more exact way.
10. Shake a support finger from itself and on itself 5 times then wrap a nut.
11. A Dinamometrichesky key with a scale in some N of m check the moment of resistance a finger provorachivaniya.
12. Turn a finger a key, doing 1 turn for 2–4 seconds. On the 5th turn check indications of the moment and compare with standard (see subsection 9.1).
13. If the moment differs from norm, a support replace.

Replacement of the top support

PERFORMANCE ORDER
1. Remove a fist.
2. Remove a collar, a cover and get a lock ring.
3. Vypressuyte a support a stripper through an opravka (1 – a deep opravka).
4. If the hinge is replaced, press it a hydraulic press through 2 opravka
(1–opravka).
5. Further assembly is carried out upside-down.
6. All fastenings of a suspension bracket tighten with the set moment.

Replacement of the bottom support

PERFORMANCE ORDER
1. Disconnect steering draft.
2. Disconnect a fist from the bottom lever.
3. Unscrew bolts and remove the bottom support.
4. Establish a new support and tighten bolts with the set moment.
5. Further assembly is carried out upside-down.