Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Toyota 4Раннер
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. 4-cylinder engines
      3.1.1. Specifications
      3.1.2. Types of repair, выполняемыe without removal of the engine from the car
      3.1.3. Installation of the piston of the 1st cylinder in VMT of a step of compression
      3.1.4. Cover of a head of cylinders
      3.1.5. A soaking-up collector
      3.1.6. Final collector
      3.1.7. Cam-shafts and pushers
      3.1.8. Head of cylinders
      3.1.9. Cover of a chain drive of cam-shafts
      3.1.10. Forward epiploon of the crankshaft
      3.1.11. Oil pallet
      3.1.12. Oil pump
      3.1.13. Flywheel (a leading disk of the hydrotransformer)
      3.1.14. Back epiploon of the crankshaft
      3.1.15. Engine mount details
   + 3.2. Engines of V6 3,0 l (1993-1994) and 3,4 l (since 1995)
   + 3.3. Dismantle and major maintenance of the engine
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes




3.1.14. Back epiploon of the crankshaft

Replacement

PERFORMANCE ORDER
1. Remove a check point (transmission). Remove a back plate.
2. The epiploon can be removed without dismantle of the oil pallet or removal of the holder of an epiploon. However such way is not recommended, as the epiploon is established in the holder with a big tightness and consequently it is possible to damage an epiploon or in the holder, or at installation. If you nevertheless want to try, a screw-driver take an old epiploon.
3. Grease a neck of the crankshaft and working edges of a new epiploon with universal konsistentny greasing and carefully establish an epiploon into place. A working edge of an epiploon very rigid therefore at installation on the crankshaft push an epiploon carefully, operating with a smooth subject. In easy blows press an epiploon into place. Sharp blows do not put, otherwise the epiploon can be damaged.
4. It is recommended to apply a method which is described below. However, here it is required to open consolidation in a back part of the pallet and to remove the holder of an epiploon.
5. Unscrew two extreme back bolts of the pallet which are screwed in the holder. With Shpatel open consolidation between a back part of the pallet and the holder of an epiploon. Unscrew bolts, remove the holder and remove the laying remains. Remove consolidation from the demountable plane of the pallet.
Prevention

Open part of the pallet close pure rags that the consolidation remains did not get during pallet fastening at assembly.
6. Having put to the holder with an epiploon on two wooden whetstones, beat out an epiploon a screw-driver from a reverse side.
7. Press in the holder a new epiploon in hammer blows through a wooden pro-rate.
8. Grease working edges of a new epiploon and a neck of the crankshaft with universal konsistentny greasing. Establish new laying of the holder of an epiploon on the block of cylinders. On the opened part of the oil pallet put with drops RTV hermetic, especially on the plane adjacent to the block of cylinders.
9. Carefully dress an epiploon with the holder on a crankshaft neck.
10. Tighten bolts of the holder with the set moment.
11. Further assembly is carried out upside-down.