Toyota 4Раннер
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
+ 3.1. 4-cylinder engines
- 3.2. Engines of V6 3,0 l (1993-1994) and 3,4 l (since 1995)
3.2.1. Specifications
3.2.2. Types of repair, выполняемыe without removal of the engine from the car
3.2.3. Installation of the piston of the 1st cylinder in VMT of a step of compression
3.2.4. Covers of heads of cylinders
3.2.5. A soaking-up collector
3.2.6. Final collectors
3.2.7. Belt of an asterisk of cam-shafts
3.2.8. Forward epiploon of the crankshaft
3.2.9. Epiploons of cam-shafts
3.2.10. Cam-shafts and pushers
3.2.11. Heads of cylinders
3.2.12. Oil pallet
3.2.13. Oil pump
3.2.14. Flywheel (a leading disk of the hydrotransformer)
3.2.15. Back epiploon of the crankshaft
3.2.16. Engine mount details
+ 3.3. Dismantle and major maintenance of the engine
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes
|
The oil pallet and adjacent details on the engine of 3,0 l
1. Cover of the oil pump
2. Leading gear wheel
3. A conducted gear wheel
4. Case
5. Epiploon
6. Sealant
7. Reduktsionny valve |
8. Spring
9, 12, 15, 19. Laying
10. For rear-wheel and/m
11, 17. Maslootrazhatel
13, 16. Maslopriyemnik
14. For all-wheel drive and/m
18. Pallet |
The oil pallet and adjacent details on the engine of 3,4 l
1. The Perepuskny pipe with a wire of the sensor of a detonation
2. For automatic transmission
3. Leading disk
4, 5. Remote laying
6. Back plate
7. Flywheel
8, 23. Engine arm
9, 20. Sealant
10. Union of a maslookhladitel
11. Laying
12. Hollow bolt
13. Maslookhladitel
14. Sensor of emergency pressure of oil
15. Maslopriyemnik
16. Pallet |
17. Stopper
18. Starter cable
19. Oil pump
21. Generator arm
22. Epiploon
24. An inlet branch pipe of cooling liquid
25. Thermostat
26. Drain stopper
27. Detonation sensor
28. The pump of cooling liquid
29. Arm
30. Maslootrazhatel
31. Union of the oil filter
32. Oil filter |
Prevention
For pallet removal on all-wheel drive cars it is required to dismantle semi-axes and a forward reducer. Therefore for pallet removal on these cars it is recommended to remove the engine as this operation is slightly simpler.
Removal
| PERFORMANCE ORDER |
| 1. Remove mud guards of the engine. |
| 2. Disconnect the battery from weight. |
| 3. Lift the car. |
| 4. On all-wheel drive cars remove semi-axes and a forward reducer. |
| 5. Merge oil and remove the oil filter. |
| 6. Remove a gear belt. |
| 7. Remove the bottom casing of a flywheel. |
| 8. Unscrew bolts and remove the oil pallet. If necessary displace in easy blows. |
|
Installation
| PERFORMANCE ORDER |
| 1. Remove from the demountable planes of the block of cylinders and the pallet the consolidation remains. Wash out the condensed planes solvent. |
| 2. Be convinced of purity of carving openings in the block of cylinders. |
| 3. Check existence on the demountable plane of the pallet of deformations, especially about openings under bolts. If necessary отрихтуйте plane hammer. |
| 4. Establish a maslootrazhatel (if acted in film). |
| 5. Check a condition of a maslopriyemnik, existence on it of cracks and a contamination of the filter of rough cleaning. |
| 6. Put the hermetic roller in diameter about 3 mm on the condensed plane of the pallet. |
| 7. Carefully establish the pallet and wrap bolts. In three-four receptions tighten pallet bolts with the set moment, beginning an inhaling in the central part. |
| 8. Further assembly are carried out upside-down. Fill in oil in the engine and replace the filter. Replace laying of an exhaust pipe of the exhaust silencer. |
| 9. Start the engine and be convinced of lack of leaks. |
|
|
|