Toyota 4 Runner/Hilux/Surf

1987-1998 of release

Repair and car operation


Toyota 4Раннер
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. 4-cylinder engines
   - 3.2. Engines of V6 3,0 l (1993-1994) and 3,4 l (since 1995)
      3.2.1. Specifications
      3.2.2. Types of repair, выполняемыe without removal of the engine from the car
      3.2.3. Installation of the piston of the 1st cylinder in VMT of a step of compression
      3.2.4. Covers of heads of cylinders
      3.2.5. A soaking-up collector
      3.2.6. Final collectors
      3.2.7. Belt of an asterisk of cam-shafts
      3.2.8. Forward epiploon of the crankshaft
      3.2.9. Epiploons of cam-shafts
      3.2.10. Cam-shafts and pushers
      3.2.11. Heads of cylinders
      3.2.12. Oil pallet
      3.2.13. Oil pump
      3.2.14. Flywheel (a leading disk of the hydrotransformer)
      3.2.15. Back epiploon of the crankshaft
      3.2.16. Engine mount details
   + 3.3. Dismantle and major maintenance of the engine
+ 4. Systems of heating, ventilation
+ 5. Fuel and exhaust systems
+ 6. Transmissions
+ 7. Transmission elements
+ 8. Brake system
+ 9. Suspension bracket and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes




3.2.13. Oil pump

Removal

PERFORMANCE ORDER
1. Remove the pallet.
2. Remove a gear belt and the bottom roller of a natyazhitel.
3. Remove a leading asterisk.
4. Remove a masloukazatel.
5. Remove the generator.
6. Remove the compressor of the conditioner and take aside.
7. Remove a compressor arm.
8. Disconnect a rod of a regulator of the hydraulic booster and take aside.
9. Remove the bottom roller of a natyazhitel.
10. Unscrew bolts and remove the pump, having hooked a screw-driver.
11. Remove a sealant and details of the reduktsionny valve.
12. Turn out cover screws.
13. Uncover and get a gear wheel.
14. Remove from the demountable planes of the pump the consolidation remains, wash out solvent.

Check

PERFORMANCE ORDER
1. Wash out all details in solvent, check existence of wear and damages.
2. Check a condition of details of the reduktsionny valve. At detection of damages the piston complete with a spring replace.
3. Check shchupy a gap between a conducted rotor and the case.
4. Check shchupy a face gap.
5. Check shchupy a gap between (arrow) rotors.
6. Compare results to the data specified in subsection 3.2.1.

Installation

PERFORMANCE ORDER
1. Get a crankshaft epiploon, having hooked a screw-driver.
2. Grease and carefully press a new epiploon.
3. Establish pump gear wheels in the case labels up.
4. Put in a pump cavity technical vaseline, lay laying, put a cover and tighten screws.
5. Grease the piston of the reduktsionny valve with fresh oil for the engine and establish valve details.
6. Wash out a condensed surface of the pump.
7. Put on a pump cover the hermetic roller.
8. Establish in the block of cylinders a new sealant.
9. Establish the pump, having combined shlitsa of a leading gear wheel with a shliyets on the crankshaft.
10. Tighten bolts in a diagonal order with the set moment.

11. Establish other details upside-down, add oil, start the engine. Check oil level repeatedly.